CCNP ENCOR 350-401: Implementing Cisco Enterprise Network Core Technologies Practice Questions Part 6

What does BGP employ to ensure a loop-free path to a destination?

Which technique separates routing tables, IP addresses, and network interfaces?

R2 can access the 192.168.10.4 network via two different routes. What would the alternative route need to do to satisfy the feasibility requirement?

Which protocol number denotes the encapsulation of an EIGRP packet within an IP packet?

Which of the following best sums up the autonomous system number employed in the EIGRP setup of a Cisco router?

The EIGRP domain includes every router that is visible. Which route will a packet that comes from a host on the 192.168.1.0/24 network and is headed to a host on the 192.168.2.0/24 network take, assuming the configurations do not change the EIGRP metric weights?

What kind of routing system allows for load balancing on lines with different costs?

How has using interface delay measured in picoseconds rather than microseconds enhanced the EIGRP routing protocol?

What are the two requirements for an EIGRP route to become active? (Select two)

Which EIGRP routing protocol feature enables quick re-convergence in the event of a route failure without DUAL recomputation?

What are the two advantages of summarizing networks within an organization that employs the EIGRP routing protocol? (Select two)

What two qualities define OSPF areas? (Select two)

Which three conditions must be met for two OSPFv2 routers to establish adjacency? (Select three)

When configuring a router, a network technician issues the following commands:
R1(config)# router ospf 11
R1(config-router)# network 10.10.10.0 0.0.0.255 area 0
What does the number 11 stand for?

What sort of neighbor relationship forms between routers R1 and R2 when OSPF is operational and converged?

Which two parameters between two OSPF routers must match in order to create a neighbor adjacency? (Select two)

Which action can be made during the planning stages of an OSPF deployment to lower router overhead by capping the size of the link state databases and LSA Type 1 and Type 2 propagation?

Which LSA type does each OSPF router advertise?

How long must pass after an LSA is not updated with a new LSA before it is deleted from the local LSBD?

When an ABR receives a type 1 LSA, what does it do?

What is contained in an OSPF area?

Which statement regarding the differences between OSPFv2 and OSPFv3 is accurate?

In global configuration mode, a network administrator types the command ipv6 router ospf 64. What outcome does this command produce?

At what level does OSPF maintain a unique LSDB?

Which type of LSA only exists on networks containing a DR?

What advantages do the two new LSA types, type 8 and type 9, bring to OSPFv3?

What TCP port is used by BGP to exchange messages between routers?

Two external BGP autonomous systems, autonomous systems 65200 and 65100, are being routed via autonomous system 65500. BGP synchronization in autonomous system 65500 is disabled. To ensure proper routing between autonomous systems 65200 and 65100, which routers should be in IBGP peer relationships?

What kind of BGP message is sent before a BGP peering session is successfully formed?

In what order is the BGP router ID determined?

On a router, a network administrator configures BGP. Which configuration procedure is required to start a BGP connection with the neighboring router?

Which BGP routers will establish peer relationships and exchange routing data?

What is the method by which routers within each AS exchange routing data?

What autonomous system would it not be appropriate to operate BGP on?

A corporation is using BGP multihoming to offer redundancy for internet connections. What approach can be taken to get around the internet transit routing issue?

BGP multihoming is being used by a business to offer redundant network connections for a number of branch sites. One of the network architecture objectives is to offer deterministic routing among business locations during failover by identifying a single location to handle branch transit traffic. Which two design standards should be used for this particular facility? (Select two)

The weight property for BGP is described by which three statements? (Select three)

What are the two definitions of private BGP communities? (Select two)

Which BGP message is sent when a BGP session error is discovered and the BGP connection is closed?

What is the IP address of the multicast group Cisco-RP-announce?

Which qualifies as a PIM sparse mode characteristic?

Which IP address is used by the Bootstrap Router (BSR) mechanism of automating the delivery of Rendezvous Point (RP) information to all Protocol Independent Multicast (PIM) routers?

A network administrator is investigating an IP multicast issue. Where can the administrator examine source S, group G, Incoming Interfaces (IIFs), Outgoing Interfaces (OIFs), and RPF neighbor information for each multicast route?

Which well-known multicast group is joined by all PIM-enabled routers to receive RP mappings?

All of the network’s VLANs have had multicast configuration and PIM sparse mode activated by an administrator. Which feature aids in lowering the amount of multicast traffic broadcast on access layer switches?

Which of the following two IGMPv3 modes is used to indicate membership in a multicast host group? (Select two)

Which of the following best represents an attribute of IP multicast routing?

Which nonproprietary mechanism does PIM employ to identify and broadcast the RP set details for each group prefix for each router in a PIM domain?

Which OSPFv3 LSA type is employed by ASBRs to publish routes that have been redistributed from other routing protocols?

Which LSAs are diminished by interarea summarization?

To determine the prefix, what notation does the IPv6 use?

If the priority of the OSPF router is set to ____________, it will never be selected as DR.

Which of the following states that DR and BDR have been chosen, and the master-slave relationship has been established?

Why does static routing be useful? (Choose all that apply)

Which of the following are true for EIGRP? (Choose all that apply)

Select the BGP states in the correct order

What is the command to configure an Extended ACL with the number 120 that allows only ICMP traffic coming from the network 192.168.1.0/24 to the host 2.2.2.2? (Choose all that apply)

Select the correct syntax for Python code to write Hello World.

Which route will be selected if there are two routes to a destination – one with RIP and the other with OSPF?

Which protocol has both distance vector and link-state properties?

What is the command to configure a static route to the 10.10.10.0/24 network going through the next hop, 20.20.20.2?

How can you set the OSPF hello timer on Cisco routers to 20 seconds?

Which of the following are IPSecurity headers? (Choose all that apply)

Which of the following letters are used to indicate the Static routes in the routing table?

In Python, how will you take user input and assign that to a variable x?

Select the true options for a link-local address. (Choose all that apply)

Which of the following is the valid host ID that comes in the prefix 200.36.11.5/28?

How can you see the EIGRP topology table on Cisco routers?

How can you configure the CGMP under the interface configuration mode of a Cisco router?

What is the version of RIP (Routing Information Protocol) used with IPv6?